Conductor Rail

Unipole Insulated Conductor

NSP - H Series

System Description


NSP-H Unipole Insulated Conductor Rail is a modern mobile power supply system. The material of the conductor rail can be copper or aluminium.The aluminium conductor is mounted with a stainless steel strip to be long service life. Any numbers of poles of conductor rail can be installed vertically or horizontally, no matter on a straight or curved system. This type of conductor rail can also be used indoor or outdoor.

Model NSP-H32-n/m

Model NSP-HT32-n/m

NSP-H32 Accessories - Current Collector

NCC-400 NCC*2-400

NSP-H32 Accessories - Current Collector

NCL-400 NCL*2-400

NSP-H32 Accessories - Carbon Brush & Spare Parts Of Collector H32CB-147

NSP-H32 Accessories - Carbon Brush & Spare Parts Of Collector

H32CB-180 H32HT-2 H32TB-2

NSP-H32 Accessories - Current Collector

NCT-500/NCT*2-500

NSP-H32 Accessories - Tow Arm

HTA-400/HTA-350

NSP-H32 Accessories - Hanger

H32HG-1/H32HG5*

NSP-H24 Accessories - Joints

H24JBT

NSP-H32 Accessories - Joint

H32JBT

NSP-H32 Accessories - End Cap

H32EC

NSP-H32 Accessories - Isolating Section

H32IS

Model - H24-n/m

Model NSP-HT24-n/m

NSP-H24 Accessories - Current Controller

NCC-200 & NCC*2-200

NSP-H24 Accessories - Carbon Brush & Spare Parts Of Collector

H24CB-130

NSP-H24 Accessories - Hanger

H24GH-1  H24GH-5*

NSP-H24 Accessories - Jointing Box

H24JBX-1 H24JBX-5*

NSP-H24 Accessories - Joints

H24JBT

NSP-H24 Accessories - End Cap

H24EC

NSP-H24 Accessories - Isolating Section

H24IS

Model NSP-H19-n/m

Model NSP-HT19-n/m

NSP- H19 Accessories - Current Controller

NCC-100 & NCC*2-100

NSP-H19 Accessories - Carbon Brush & Spare Parts Of Collector

H19CB-100

NSP-H19 Accessories - Tow Arm

HTX-350

NSP-H19 Accessories - Hanger

H19GH-1  H19HG-2  H19GH-5*

NSP-H19 Accessories - Hanger

H19GH-13  H19HG-35*

NSP-H19 Accessories - Jointing Box

H19JBX-1  H19JBX-5*

NSP-H19 Accessories - Joints

H19JBT

NSP-H19 Accessories - End Cap

H19Ec

NSP-H24 Accessories - Isolating Section

H19IS

NSP- H Accessories - Expansion Joint

EJ

Support Installation:

 Fix the two supports of both sides of the track(welding or bolt) and adjust to the horizontal state(add 1 or 2 points to meet the length of the wiring route).

  • Read More

    Take the wiring between the two supports as the benchmark, the rest supports should be installed according to the standard distance(1800 mm for bolt and 2000mm for welding), to ensure the depth of parallelism of the conductor rail between the height of the trackless than 10 mm.


    The connection part of the conductor and the connector should be polished with an abrasive cloth to remove the oxide layer, apply the electrical conductive pastes and screw the bolt, double-check if the seam of the guides is in minimum. 


    The installation of the current collector: Define the length of the tow arm unit according to the poles of electrode and installation space. 120±5mm distance should be ensured in distance between the upper end and down end of the conductor rail(refer to the installation diagram of the conductor rail for more details) 


    Endcap: Install the end caps on both sides and tighten them with rubberized fabric. 


    Inspection: Inspect the depth of parallelism between the conductor rail and operation track of the hoisting unit and control the depth within 20mm, make a test run and check the running state of the flake passing through each nodal point, tighten all the fastening piece if some problems occur, try to run one month without interval and tighten all fastening pieces again.